Hi. This must be the last job on my Tesla Coil build. I need to make an earthing point on the main Tesla coil body. Most of the earth leads in my Tesla are connected to the earthing point on the neon transformer. These are
1. Connection to the strike rail underneath the primary coil perspex covering disc.
2. Connection to the lower terminal on the secondary coil.
3. Connection to the central rail on the Terry filter.
So I need to connect this point to my earthing plate on the conservatory wall. I could just run a wire from the earth plate through one of the vent holes in the Tesla base to the earth terminal on the neon transformer. The problem with this solution is that it would be impossible to remove this lead as the ring terminal needed on the end of the wire will not pass through the vent hole. Even if I enlarge the vent hole it would still involve removing one of the perspex walls of the base unit to attach/detach this wire.
After some thought I decided to fit an earthing point on the outside of the back perspex wall of the main Tesla unit. This would consist of 2 copper terminal lugs, one mounted inside, one mounted outside, connected through the perspex by a M6 bolt.
Above is the hardware for the terminal, I will probably replace the stainless M6 bolt with a homemade copper stud but will need to procure an M6 die first.
I made a small lead that finishes in a ring terminal to connect to the new earth point. I fitted the lead to give me a better idea where to site the hole for the terminal.
Marked up the point to drill the 6mm hole. I drilled the hole freehand, there were no obstructions and it was pretty easy to keep the drill at right angles to the perspex.
Result was a nice neat 6mm hole. My OCD placed it on the centre with the vent holes and level with the end of the neon transformer.
Here's the hardware fitted. I used 2 of the copper lugs from Alan at teslastuff.com. These are the best quality electrical lugs I have seen.
The terminal was connected to the short lead from the neon transformer earth point and the perspex sidewall replaced. Job done.
If you like this blog you can show your support by one or all of these.
1. +1 my blog and email it to a friend.
2. Follow me.... It's good to know someones interested.
3. Leave a comment.... All are appreciated.
This is my blog of current hobbies, at the moment that happens to be all things Tesla so I have decided to build a Tesla coil and, as usual, I will go completely over the top with it.
Showing posts with label tesla coil kit. Show all posts
Showing posts with label tesla coil kit. Show all posts
Monday, 12 August 2013
Wednesday, 28 December 2011
Primary coil assembly
With all the combs finished and the primary coil approximately shaped to the correct spiral I decided to thread the primary copper tubing into the combs. It was slow going as you have to move the combs along the tubing one at a time working around the spiral.
It took about an hour to get all the combs into the right position. Next I drilled out the mounting holes in the anti-strike disc to 4mm and placed it over the top of the comb assembly. I noticed that the holes in the combs were not going to line up with the holes in the anti-strike disc. The combs were to far out from the centre by about 5mm. After my initial panic I realised all I needed to do is tighten up the spiral to bring the combs closer to the centre. This done, I fitted the 24 10mm M4 nylon bolts through the anti-strike disc into the support combs.
Here you can see the 3 nylon bolts that fasten each comb to the anti-strike disc.
The disc underneath the primary coil is still covered in masking tape as I have yet to make some electrical connections so may need to do some more marking up and drilling.
At the moment the primary coil assembly just sits on top of the perspex disc underneath. I will add some system that will allow the primary to be located into position, perhaps locating pegs or guide blocks.
It took about an hour to get all the combs into the right position. Next I drilled out the mounting holes in the anti-strike disc to 4mm and placed it over the top of the comb assembly. I noticed that the holes in the combs were not going to line up with the holes in the anti-strike disc. The combs were to far out from the centre by about 5mm. After my initial panic I realised all I needed to do is tighten up the spiral to bring the combs closer to the centre. This done, I fitted the 24 10mm M4 nylon bolts through the anti-strike disc into the support combs.
Here you can see the 3 nylon bolts that fasten each comb to the anti-strike disc.
The disc underneath the primary coil is still covered in masking tape as I have yet to make some electrical connections so may need to do some more marking up and drilling.
At the moment the primary coil assembly just sits on top of the perspex disc underneath. I will add some system that will allow the primary to be located into position, perhaps locating pegs or guide blocks.
Subscribe to:
Posts (Atom)